Page 2 of 2
Re: Oil Drain Hose
Posted: Tue Dec 17, 2019 3:52 pm
by Bfun220
cmattj wrote: Tue Dec 17, 2019 1:57 pm
AsLan7 wrote: Tue Dec 17, 2019 12:42 pm
samuri33 wrote: Tue Dec 17, 2019 12:38 pm
BBP, you should have seen the pump I bought to pull it up the dipstick. I got it off of Amazon for like $50, no where in the description did it say it takes 40 strokes per gallon. The 496 holds 9 quarts! I sent that sucker back to Amazon!
.
Go with the Moeller S33. I pump it maybe 10-15 times and the vacuum is created. It will suck a quart of oil out faster than Cmattj sucks down a lemonade.
.
I accept that challenge
My money's on cmattj.
Re: Oil Drain Hose
Posted: Tue Dec 17, 2019 4:01 pm
by akorcovelos
I have a pneumatic fluid extractor that runs on shop air and will suck the pan dry in about 2 minutes, one of the best maintenance tools I've bought. I use it on everything now, except lemonade, like Matt I prefer the old fashion way for that.
Re: Oil Drain Hose
Posted: Tue Dec 17, 2019 6:11 pm
by Big Block Power
Bfun220 wrote: Tue Dec 17, 2019 3:52 pm
cmattj wrote: Tue Dec 17, 2019 1:57 pm
AsLan7 wrote: Tue Dec 17, 2019 12:42 pm
.
Go with the Moeller S33. I pump it maybe 10-15 times and the vacuum is created. It will suck a quart of oil out faster than Cmattj sucks down a lemonade.
.
I accept that challenge
My money's on cmattj.
Mine also!
Re: Oil Drain Hose
Posted: Tue Dec 17, 2019 6:12 pm
by Big Block Power
samuri33 wrote: Tue Dec 17, 2019 1:02 pm
Lockey14s wrote: Tue Dec 17, 2019 12:57 pm
good luck! its extremely tight with the big blocks. my 3.0 had a swivel on it so you could swing it around. made it a little easier. it was also chained to the drain plug tho.
samuri33 wrote: Tue Dec 17, 2019 12:41 pm
I really want to try an route the drain hose out the bilge drain hole, but the damn bilge pump looks like it might be in the way and it's hard to see under there! I might have to send my 4 year old under there to route the hose around the bilge pump and out the drain plug. Hope he doesn't get stuck!
Personally, I wish Cobalt would've routed the hose to the drain when they installed the engine and bilge pump plate. I would why they didn't.
You and A7 should get together on a weekend and each of you could just pull the engine out to change the oil
Re: Oil Drain Hose
Posted: Tue Dec 17, 2019 6:25 pm
by Big Block Power
samuri33 wrote: Tue Dec 17, 2019 12:38 pm
Big Block Power wrote: Tue Dec 17, 2019 6:12 am
Don't bother. It's easier to suck it out.
BBP, you should have seen the pump I bought to pull it up the dipstick. I got it off of Amazon for like $50, no where in the description did it say it takes 40 strokes per gallon. The 496 holds 9 quarts! I sent that sucker back to Amazon!
Warm up the pull first no matter what method you use. Make sure you have water flowing out the drive. Lol
Then connect the 12v oil extractor and put the other end in a 10qt cooler.
2 minutes and done.
Re: Oil Drain Hose
Posted: Sat Dec 21, 2019 10:58 am
by Ytmsn
cmattj wrote: Tue Dec 17, 2019 1:57 pm
AsLan7 wrote: Tue Dec 17, 2019 12:42 pm
samuri33 wrote: Tue Dec 17, 2019 12:38 pm
BBP, you should have seen the pump I bought to pull it up the dipstick. I got it off of Amazon for like $50, no where in the description did it say it takes 40 strokes per gallon. The 496 holds 9 quarts! I sent that sucker back to Amazon!
.
Go with the Moeller S33. I pump it maybe 10-15 times and the vacuum is created. It will suck a quart of oil out faster than Cmattj sucks down a lemonade.
.
I accept that challenge
My money is on Matt as I've seen him in action. Just sayin....
Re: Oil Drain Hose
Posted: Sat Dec 21, 2019 8:13 pm
by cmattj
Ytmsn wrote: Sat Dec 21, 2019 10:58 am
cmattj wrote: Tue Dec 17, 2019 1:57 pm
AsLan7 wrote: Tue Dec 17, 2019 12:42 pm
.
Go with the Moeller S33. I pump it maybe 10-15 times and the vacuum is created. It will suck a quart of oil out faster than Cmattj sucks down a lemonade.
.
I accept that challenge
My money is on Matt as I've seen him in action. Just sayin....
There’s my wingman Ytmsn.... should I falter.
Spring training ??
